View all downloads |
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Continuous Duplex Mixer |
MCD-4 |
1012-901 |
117303 |
| >> CURRENTLY RENTED - CALL FOR AVAILABILITY << Nominal Capacity: 1 tons per hour
Construction Details
- 304 Stainless steel construction in product contact areas
- Fully welded tank
- 7 Gauge tank thickness
- 10 Gauge cover thickness
- Solid bar shafting
Finish Details
- All exterior surfaces to be ground to 36 grit finish
- All interior surfaces to be 2B (100-120 grit) finish
- Product contact welds are continuous and ground to finish
- Non-product contact welds are intermittent and gaps filled
with food grade Devcon
- All steel components to be painted with one primer coat and
one top coat (white)
Standard Design Features
- Solid twin shaft paddle type agitators - one shaft right hand
and one shaft left hand
- One shaft extended for drive
- 46 Fully adjustable and replaceable solid paddles with
machined washers to lock paddles to shafts
- Three (3) 2-bolt flange bearings
- Double lip type shaft seals
- One (1) hinged & clamped domed cover with viewports and spray nozzle ports
- One (1) hinged cover with flanged inlet
- Closed cell neoprene gaskets
- Standard flanged bottom outlet discharge
- Counter-rotating gear connecting drive, oil bath lubrication with
oil tight enclosed guard
Standard Components
- 3 HP, 1800 RPM 3/60/230-460V inverter duty motor,
explosion proof, Class II, Div 2, Group G
- Drive Class I application, complete with shaft mounted gear
reducer for a shaft speed of 175 RPM
- Bolted inlet & discharge transitions |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Heating/Cooling Conveyor |
6U8-JS |
1008-901 |
117289 |
| Construction Details
- 304 Stainless steel in product contact areas
- U-Trough style housing, 8 feet long inside
- Integral jacket for cooling fluid
- Internal flow baffles
- Designed for low pressure, 14.9 psig max. (non-ASME coded jacket)
- Integral jacket for insulation
- 2 HP, TEFC, 1750 RPM, 3/60/230-460 motor
- Foot mounted gear reducer for a nominal speed of 20 RPM
- Split packing gland seals with temperature appropriate packing and set up with air purge
- Flange block bearings for auger support
- Portable base with instrumentation |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| ES Sanitary Blender |
ES-300 |
0604-902 |
117026 |
| Economic Sanitary Blender, capacity: 2.1 cu. ft. 65% full and 3.5 cu. ft. to top of mixer agitator, 304 SS construction in product contact areas, Interior welds continuous and ground smooth to radius for sanitary use, Interior surfaces polished to 80 grit, Exterior welds intermittent ground smooth – gaps sealed, Exterior surfaces Mill finish, Exterior carbon steel surfaces white epoxy, Flanged journal design for top removal of cylinder for ease of cleaning. Ribbon or Paddle agitators available, 1.5 hp, 3/60/230-460, 1800 RPM, washdown, inverter duty gearmotor for ~76 rpm final speed, Shaft seals are packing gland seals with air purge |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Ribbon Blender |
M-244 |
0507-903 |
116991 |
| 8 cu.ft. blender working capacity, mild steel, double ribbon agitator, single lip type shaft seals, flanged center discharge, 5 HP, 1800 RPM TEFC 3/60/230/460 Motor, Mixer Drive Class I application for a mixer speed of 56 RPM |
Brochure: download
|
|
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Mixall Ribbon Blender |
M-368 |
0507-904 |
116992 |
| Blender capacity: 38.6 cu. ft. 65% up the mixer agitator shaft, 63.6 cu. ft to top of mixer agitator, All mild steel construction, Interior welds are continuous and ground smooth, Exterior welds are intermittent and wire brushed, Exterior surfaces one (1) coat primer and one (1) blue shop coat, Double ribbon agitator, Cylinder rotation: Clockwise from drive end, Single lip type shaft seals, Flanged center discharge (6" 150 # flange pattern), 20 H.P., 1800 RPM TEFC 3/60/230/460 Motor, Mixer Drive Class I application for a mixer speed of 37 RPM |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Paddle Mixer |
ES300-J |
0901-902 |
117217 |
| Jacketed Paddle Blender, capacity: 2.1 cubic feet 65% full and 3.5 cubic feet to top of mixer agitator, 304 SS construction in product contact areas, Interior welds continuous and ground smooth, Interior welds polished to 80 grit, Exterior welds intermittent ground smooth – gaps sealed, Exterior surfaces mill finish, Exterior carbon steel surfaces Steel-It, Flanged journal design for top removal of cylinder for ease of cleaning, Paddle agitator, Integral jacket for heating or cooling is rated for 14.9 psig maximum, 1.5 hp, 3/60/230-460, 1800 RPM, washdown, inverter duty gearmotor for ~76 rpm final speed, Shaft seals are packing gland seals with air purge |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Continuous Duplex Mixer |
MCD-4 |
0706-901 |
117089 |
| >> CURRENTLY RENTED - CALL FOR AVAILABILITY << Nominal Capacity: 1 tons per hour, 304 Stainless Steel Construction in product contact areas, Product contact surface finish, 2B (100 � 120 grit), Interior welds to be continuous and ground to finish, Non-product contact welds, intermittent ground to finish 36 grit, voids filled with food grade Devcon, Mild steel component finish paint, one prime and one shop coat (motor, reducer, bearings, gear case), 4 �-0� x 12� inside dimension, 46 fully adjustable pitch, replaceable solid paddles, One shaft extended for drive, Four (2) bolt flange bearings, One hinged and clamped cover with view port and one bolted cover with inlet, Double lip type shaft seals on mixing tank, End discharge flanged bottom outlet, Twin shafts with counter rotating gear connecting drive, oil bath, Lubrication with oil tight enclosed guard, 3 H.P., 1800 RPM Standard Duty, 3/60/230-480V Motor, Class I drive with speed reducer, V-belt drive for a final speed of approximately 175 RPM |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Continuous Duplex Mixer |
C-62 |
0812-902 |
117210 |
| >> CURRENTLY RENTED << Mild steel construction
6’ x 26-5/8 inside dimensions
All interior and exterior surfaces to be uniform mill finish
Interior Welds to be continuous and ground smooth
External Welds to be intermittent, not ground and wire brushed
Exterior mild steel surfaces to have one coat primer and one shop coat
48 paddles for both shafts, solid, bolted for rotational adjustment and replaceable
One spray manifold (pump & plumbing by others
One shaft extended for drive
Solid twin shafts with counter rotating gear connecting drive, oil bath lubrication with oil tight enclosed guard
Bolted and gasketed flat covers with single flanged inlet
End discharge flanged bottom outlet
Four (4) bolt self-aligning flange bearings
Lip type shaft seals
7.5 HP, 1800 RPM, 3/60/230-460V TEFC Inverter duty motor Class I drive with speed reducer, V-belt drive for a final speed of approximately 300 RPM
Installation, wiring and controls by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Split-Tube Conveyor |
4SC12 |
0805-905 |
117211 |
| 4" diameter screw x 12' long, Nominal capacity: 200-380 cu.ft/hr, 304 Stainless steel construction in product contact areas, Product contact surface finish 2B, Exterior surfaces, mill finish, Continuous welded flighting, ground smooth to 80 grit, Interior welds are continuous, ground smooth to 80 grit, Exterior welds are intermittent, wire brushed, Mild Steel exterior finish-paint one prime and one coat white epoxy, Covers on trough: Gasketed, hinged and fastened into place w/ plastic hand knobs w/ mounted not wired limit switch, 2-1/4 Ft3 hopper with safety grating, Rotating mechanical shaft seal at inlet end, Single lip at discharge end, Carbon steel portable base with hydraulic jack for angle adjustment, 2 HP, 1750 RPM 3/60/230-460V washdown inverter duty motor, 10:1 shaft mounted gear reducer for an auger speed of 175 RPM, Wiring, controls and installation by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Split-Tube Conveyor |
6SC9 |
0604-902 |
117024 |
| >> CURRENTLY RENTED - CALL FOR AVAILABILITY << 6" diameter screw x 9’-2” long, Sanitary Construction, 304 Stainless steel construction in product contact areas, Product contact surface finish – 2B, Exterior surfaces, mill finish, Continuous welded flighting, ground smooth to 80 grit, Interior welds are continuous, ground smooth to 80 grit, Exterior welds are intermittent, wire brushed, Mild Steel exterior finish - paint one prime and one coat white epoxy, Covers on trough: Gasketed, hinged and fastened into place w/ plastic hand knobs w/ mounted not wired limit switch, 2-1/4 Ft3 hopper with safety grating, Rotating mechanical shaft seal at inlet end, Single lip at discharge end, Carbon steel portable base with hydraulic jack for angle adjustment, 2 HP, 1750 RPM 3/60/230-460V washdown duty motor, 10:1 shaft mounted gear reducer for an auger speed of 175 RPM, Wiring, controls and installation by customer
|
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Split-Tube Conveyor |
6SC10 w/ conical hopper |
0706-902 |
117099 |
| >> CURRENTLY RENTED - CALL FOR AVAILABILITY << 304 SS construction, 6” diameter screw x 10’ long with 2/3 pitch inlet flighting, balance full pitch, Continuous welded flighting, ground to 120 grit finish, Interior welds are continuous, ground to 120 grit finish, Exterior welds are intermittent, ground smooth, Interior surface, uniform 120 grit finish, Exterior surfaces to have a uniform mill finish, Mild steel components to be one coat primer & one coat white epoxy, Cover on trough: gasketed, hinged & fastened in place with plastic handknobs, with mounted, not wired limit switch, Mild Steel Portable base with two (2) rigid and two (2) swivel casters with brakes and hydraulic jack for angle adjustment, 5 ½ cu.ft. conical hopper with grating and ribbon style agitator with mounted not wired limit switch (optional 4 Ft3 and thru-flow hoppers available), Mechanical shaft seal on inlet, Lip type shaft seal on discharge end, 2 HP, 1800 RPM, TEFC 3/60/230-460 Standard duty motor, 10:1 gear reducer for an auger speed of 175 RPM, Wiring, controls and installation by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Split-Tube Conveyor |
6SC10 |
0805-901 |
117167 |
| >> CURRENTLY RENTED - CALL FOR AVAILABILITY << 6" diameter screw x 10' long with 2/3 pitch inlet flighting, balance full pitch flighting, Auger has sleeve caps & acorn nuts for sanitary application, 304 Stainless steel construction, in product contact areas, Interior surfaces uniform 120 grit finish, Exterior surfaces, uniform Scotch-Brite finish, Continuous weld on both sides of flighting, Welds in contact with product continuous and ground to 120 grit finish, Welds not in contact with product intermittent and ground smooth, gaps filled with Devcon, Covers on trough: Gasketed, hinged and fastened into place w/ plastic hand knobs, w/120 VAC limit switch (mounted not wired), Mild Steel Portable base with two (2) rigid and two (2) swivel casters with brakes, and hydraulic jack for angle adjustment, 2-1/4 ft3 hopper with bolted safety grating, 6" Standard pipe stub discharge, Exterior mild steel components (motor, bearings, etc.) to be one coat primer & one coat white epoxy, Rotating mechanical shaft seal on the drive and single lip seal on discharge end, 2 HP, 1800 RPM 3/60/230-460V TEFC (4:1) Inverter duty motor, 20:1 gear reducer for final auger speed of approx. 88 RPM, Standard cleanout with 120 VAC limit switch (mounted not wired), Controls, Wiring and installation by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Split-Tube Conveyor |
6SC12.5 |
0810-901 |
117200 |
| 6" diameter screw x 12.5' long with full pitch flighting, 2/3 pitch at hopper, 304 Stainless steel construction, in product contact areas, Interior surfaces uniform #2B finish (80 grit), Exterior surfaces, mill finish, Continuous weld on both sides of flighting, Welds in contact with product continuous and ground to 80 grit finish, Welds not in contact with product intermittent and wire brushed, Covers on trough: Gasketed, hinged and fastened into place w/ plastic hand knobs w/120 VAC limit switch (mounted not wired), Mild Steel Portable base with two (2) rigid and two (2) swivel casters with brakes and hydraulic jack for angle adjustment, 5-1/2 cu. ft hopper with bolted safety grating, 6" Pipe stub outlet, Exterior mild steel components (motor, bearings, etc.) to be one coat primer & one coat white epoxy, Rotating mechanical shaft seal on the drive and single lip seal on discharge end, 3 HP, 3450 RPM 3/60/230-460V TEFC Standard duty motor, 30:1 gear reducer for a auger speed of 115 RPM, Standard cleanout with 120 VAC limit switch (mounted not wired), Controls, wiring, hopper cover and installation by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Split-Tube Conveyor |
6SC12 - Carbon Steel |
0901-901 |
117216 |
| 6" diameter screw x 12' long with 2/3 pitch inlet flighting, balance full pitch flighting; Carbon Steel construction; Mill finish all surfaces; Continuous weld on both sides of flighting; Welds in product contact are continuous and wire brushed; Welds not in product are intermittent and wire brushed, gaps filled with Devcon; Covers on trough: Gasketed, hinged and fastened into place w/ plastic hand knobs and equipped w/120 VAC limit switch (mounted not wired); Mild Steel Portable base with two (2) rigid and two (2) swivel casters with brakes and hydraulic jack for angle adjustment; Four cubic foot hopper with bolted safety grating; 6" Standard pipe stub discharge; Exterior surfaces have one coat primer & one blue shop coat; Double lip seal on the drive and single lip seal on discharge end; 2 HP, 1800 RPM 3/60/230-460V TEFC motor; 10:1 gear reducer for a auger speed of 175 RPM; Standard cleanout with 120 VAC limit switch; Controls, installation, and wiring by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Tubular Conveyor - Stainless |
6C12 |
0805-903 |
117169 |
| 6" diameter screw x 12' long with 2/3 pitch inlet flighting, balance full pitch flighting,
304 Stainless steel construction, in product contact areas, Interior surfaces uniform mill finish, Exterior surfaces, uniform Scotch-Brite finish, Continuous weld on both sides of flighting, Welds in contact with product continuous and ground smooth, Welds not in contact with product intermittent and ground smooth, gaps filled with Devcon, Mild Steel Portable base with two (2) rigid and two (2) swivel casters with brakes and hydraulic jack for angle adjustment, 5 1/2 cu. Ft Nominal capacity hopper with bolted safety grating, 6" Standard pipe stub discharge with lip for flex boot, Exterior mild steel components (motor, bearings, etc.) to be one coat primer &
one coat (blue), Rotating mechanical shaft seal on the drive and single lip seal on discharge end, 2 HP, 1800 RPM 3/60/230-460V TEFC (4:1) Inverter duty motor, 10:1 gear reducer for a auger speed of 175 RPM, Standard cleanout with 120 VAC limit switch (mounted not wired), Controls, Wiring and installation by customer |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Tubular Conveyor |
6C12 |
0805-904 |
117170 |
| 6" diameter screw x 12' long with 2/3 pitch inlet flighting, balance full pitch flighting, Carbon steel material of construction, Interior and exterior surfaces uniform mill finish, Continuous weld on both sides of flighting, Welds in contact with product continuous and wire brushed, Welds not in contact with product intermittent and wire brushed, gaps filled with Devcon, Mild Steel Portable base with two (2) rigid and two (2) swivel casters with brakes and hydraulic jack for angle adjustment, 5 1/2 cu. Ft Nominal capacity hopper with bolted safety grating, 6" Standard pipe stub discharge with lip for flex boot, Exterior mild steel components to be one coat primer & one shop coat (blue), Double lip seal on the drive and single lip seal on discharge end, 2 HP, 1800 RPM 3/60/230-460V TEFC (4:1) Inverter duty motor, 10:1 gear reducer for a auger speed of 175 RPM, Standard cleanout with 120 VAC limit switch (mounted not wired), Controls, Wiring and installation by customer. |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| U-Tough Conveyor |
12U11 |
0507-902 |
116929 |
| 12” Diameter Screw x 11’ long, Mild steel construction, Open formed U-Trough 3/16” thick, All interior & exterior welds intermittent and not ground, Bolted & gasketed flat covers, Lip type shaft seals, Supported by mild steel frame, 12” wide x 25” long feed inlet without flange, 12” diameter discharge spout, 7-1/2 H.P., 1800 RPM, 3/60/230-460V standard duty motor, Conveyor Drive: 10:1 ratio for a 175 RPM drive speed, Mild steel finish with one coat primer & one coat shop blue, Wiring, controls and installation by customer
|
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Centrifugal Sifter |
P7x11 |
0805-909 |
117175 |
| 304 stainless steel working parts in product contact areas, Product contact stainless steel surfaces to be 2B finish, Welds in product contact to be continuous and ground to 80 grit min., Welds not in product contact to be intermittent, ground to 80 grit, gaps filled with Devcon, Mild steel surfaces one coat primer & one coat white epoxy, Flanged inlet, Worm type auger to control product in feed, Adjustable tension restricted end sieve frame, One (1) compliment of customer specified nylon sieves, Four blade adjustable paddle assembly, Self-aligning outboard bearing, Bolted and gasketed dust-tight inspection/cleaning doors, 1 H.P., 1800 RPM, TEFC standard duty motor 3/60/230-460V, drive & guard, Direct drive with the motor, reducer and guard with a 2:1 reduction for a paddle speed of approx. 870 RPM, Controls, wiring, stand and installation by customer |
Brochure: download
|
|
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Centrifugal Sifter |
P7X22 |
0811-903 |
117204 |
| Approximate over-all dimension 66 length x 22 depth x 34 width,
Type 304 stainless steel construction for parts in contact with product,
Product contact surfaces to have a mill finish, Stainless surfaces not in product contact have mill finish,
External steel surfaces one coat primer & one coat bue epoxy, Welds in product contact to be continuous and wire brushed, Welds not in product contact are intermittent and wire brushed
Worm type auger to control product in feed, Adjustable tension restricted end sieve frame, Four blade adjustable paddle assembly, Self-aligning outboard bearing with lip type shaft seals,
Hinged dusttight inspection/cleaning doors, 2 H.P., 1800 RPM, TEFC motor 3/60/230-460V, drive & guard, Direct drive with the motor and reducer C faced together. The reducer gives a 2:1 reduction and a paddle speed of 870 RPM |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Lumpbreaker |
#18 |
1007-901 |
117279 |
| 304 Stainless steel construction, All surfaces polished to 80 grit finish, Product contact welds continuous, polished to 80 grit, Non-product contact welds intermittent, polished to 80 grit, gaps filled with Devcon, Flanged inlet and outlet with 12" x 17.5" inside dimensions, 1-1/2" Square solid shafts with square pins, rotary and fixed designed to intermesh, Counter-rotating gear connecting drive, oil bath lubrication with oil tight enclosed guard, Shaft speeds of 354 RPM and 513 RPM, Flanged bearings on shafts, 5 H.P., TEFC, 1800 RPM, 3/60/230-460 Standard duty motor, Belt and sheave speed reduction with OSHA approved guards, Exterior mild steel surfaces painted one coat each primer & S. Howes standard blue
> Option: perforated plate mounted below the pins to ensure lumps are broken to an appropriate size (3/8” and 1/4” holes available from stock)
|
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Power Grater |
PG-26 |
0404-459 |
115960 |
| For soft to medium hard product size reduction without producing excessive fines. 304 SS constriction, capacity is 8000 lbs/hr (approx), 4 sq. ft. of screen area, 5 Hp, 3/60/230-460 |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Power Grater |
PG-26 |
0902-903 |
117219 |
| For soft to medium hard product size reduction without producing excessive fines. 304 SS constriction, capacity is 8000 lbs/hr (approx), 4 sq. ft. of screen area, 5 Hp, 3/60/230-460 |
Brochure: download
|
|
Click for detail
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Knife Cutter |
KC11 |
0805-910 |
117176 |
| Nominal rate: 6,000 to 7,000 lb/hr (standard bulk materials), Mild steel construction, Exterior finish with one coat primer and one shop coat, Flanged inlet chute, Bottom outlet, Six (6) removable bed knives, Five (5) removable rotary knives, Removable screen perforated to customer specifications, 15 H.P., TEFC, 1800 RPM 3/60/460V Motor, V-belt drive and sheaves with guard, Unit and drive supported on framework, Wiring, controls and installation by customer |
Brochure: download
|
|
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Knife Cutter |
KC11 |
0811-902 |
117203 |
| Nominal rate: 6,000 to 7,000 lb/hr (standard bulk materials), Mild steel construction, Exterior finish with one coat primer and one shop coat, Flanged inlet chute, Bottom outlet, Six (6) removable bed knives, Five (5) removable rotary knives, Removable screen perforated to customer specifications, 15 H.P., TEFC, 1800 RPM 3/60/460V Motor, V-belt drive and sheaves with guard, Unit and drive supported on framework, Wiring, controls and installation by customer |
Brochure: download
|
|
Click for detail
|
Make
|
Model |
Shop
Number |
Machine
Number |
| Granulator |
#74 |
0612-901 |
117058 |
| Heavy duty iron castings and a tubular steel frame. The interior of the Granulator has a replaceable wear plate, collar and seal in the upper mechanism. The feed spout consists of an adjustable slide gate to regulate product flow into the Granulator. One set of Granulator rings are included along with a 15 H.P., TEFC, 1800 RPM 3/60/230-460V motor supported on a tubular base. All mild steel approximately 28” x 28” x 48”. Wiring, controls and installation by customer. This unit is typically for cutting grains such as corn. Call our office for possible capacities. |
Brochure: download
|
|
|
